Axles, Shafts, Joints and Couplings

These high pressure grease guns have an improved plunger for complete grease removal for both cartridge and bulk grease loadingKey FeaturesHeavy duty manual grease gun 3-way filling operation, standard 400g cartridge, suction or bulk fill up to 500cc Standard 400g cartridge (included)..

This is a Brand New Kit of TWO Stub Axles for the Left & RightThey have new top Bushes, Pins, Washers and Bushes and are ready to installThe Kit also comes with two new Hub Nuts(Once fitted they must be greased fully using a grease gun until the grease goes all the way through..

This is the old fashioned Castle Slotted Type Nut that requires locking with a split pin through the hubto fit:Classic Fiat 500 all early models  (from 1957 to 1969)Fiat 600Fiat 850If you have any questions or queries please contact our office for help..

Drive Shaft Clip(for 17mm Drive Shaft)to fit:Classic Fiat 500 N EARLY MODELSIf you have any questions or queries please contact our office for help..

Drive Shaft Clip(for 19mm Drive Shaft)to fit:Classic Fiat 500 N,D,F early modelsIf you have any questions or queries please contact our office for help..

Drive Shaft Clip(for 24mm Drive Shaft)to fit:Classic Fiat 500 F/L & R all models (from 1966 to 1974)Fiat 126 all modelsFiat 600If you have any questions or queries please contact our office for help..

This Aluminium Joint or Coupling is fitted to the Drive ShaftHas Rubber inside and Splined in the middle to mate with the Drive ShaftDimmensions:Circumference 22cmDepth 5cmDiameter 7cmto fit:Classic Fiat 500 N/DIf you have any questions please fe..

This Aluminium Joint or Coupling is fitted to the Drive ShaftHas Rubber inside and Splined in the middle to mate with the Drive ShaftDimmensions:Circumference 22cmDepth 5cmDiameter 7cmto fit:Classic Fiat 500 DIf you have any questions please feel ..

Brand NewOE QualityMade in ItalyAluminium with rubber damper inside, very common to breakDimmensions:Circumference 26cmDepth 4.5cmDiameter 8cmto fit:Classic Fiat 500 F/L/R/G (1966 to 1973)Fiat 126 all modelsFiat 600 all models..

OE QualityMade in ItalyAluminium with rubber damper inside, very common to breakSupplied with4x Bolts & Spring Washers RIC-9421x Rear Hub Nut-RIC-684Dimmensions:Circumference 26cmDepth 4.5cmDiameter 8cmto fit:Classic Fiat 500 F/L/R/G (..

Set of FOUR Bolts & Spring Washers to fit the drive shaft coupling and flangeFiat Part No: 16044121to fit:Classic Fiat 500 all modelsFiat 126 all modelsFiat 600If you have any queries or questions please contact our office for help..

OE Quality PartsMade in ItalyDiameter of Shaft 19mmThis kit consists of,2x Drive Shafts(19mm diameter)2x Drive Shaft Flange2x Shaft End Springs2x Clips2x Inner Boots2x Outer Bootsto fit:Classic Fiat 500 N,D,F models (up to 1968)Ther..

OE Quality PartsMade in ItalyLargest Diameter available 24/25mm (this measurement can vary between 22mm and 25mm)This kit consists of,2x Drive Shafts(24/25mm diameter)2x Drive Shaft Flange2x Shaft End Springs2x Clips2x Inner Boots2x Outer Bootst..

Brand NewThis is a new improved high quality modified Drive Shaft KitThe Metal Flanges have been modified and reinforced so they are much stronger than the original as they can be prone to breaking. These are four bolt fitting so double check the fitting of your old flanges.Largest ..

These Metal Nuts are not threaded but lock onto the end of the Drive Shaft inside the Gearbox to lock in to placeThere are TWO Nuts per Drive ShaftSold as a PAIR (2)to fit:Classic Fiat 500 all models N/D/F/L/R/GFiat 126 all modelsIf you have any questions please con..

This small Spring is located at the wheel end of each drive shaft to keep the tension and stop any knocking(for earlier thinner type 17 & 19mm Drive Shaft)to fit:Classic Fiat 500 D/F  (up to 1970)If you have any queries or questions please contact our office for h..

This small Spring is located at the wheel end of each drive shaft to keep the tension and stop any knocking(for later larger type 24mm Drive Shaft)to fit:Classic Fiat 500 F/L & R (up to 1974)Fiat 126 all modelsIf you have any queries or questions please contact our..

Front Grease Cap fits on the Front Hub and acts as a dust & dirt shieldto fit:Classic Fiat 500 all modelsFiat 126 early models (594cc)If you have any questions please contact us for help..

Connects the Gear Linkage assembly to the Gearbox in order to select GearsThis part has a rubber joint in the middle that after a while will perish and make itdifficult to select gearsto fit:Classic Fiat 500 all modelsFiat 126 all models..

A professional grease for the professional user, a high quality product manufactured in the UKKey FeaturesA heavy duty premium quality highly versatile multi-purpose lithium grease Operating temperature range -20 C to + 140 C High degree of corrosion protection Excellent extreme pre..