Rubber Boots and Gaiters

This Inner Drive Shaft Boot is clipped onto the outside of a metal flangeWould normally fit on the Left Hand Side of the vehicleIt has a built in Oil Seal to stop oil leaking and fits onto the Drive Shaft with a incapsulated plastic Bush(No 7 in the diagram)Diameter of base..

This Inner Drive Shaft Boot is clipped onto the outside of a metal flangeWould normally fit on the Left Hand Side of the vehicleIt has a built in Oil Seal to stop oil leaking and fits onto the Drive Shaft with a incapsulated plastic Bush(No 7 in the diagram)Diameter of base..

This Boot fits onto the drive shaft on the inside (engine/gearbox side)It has an built in Oil Seal and incapsulated plastic bush to fit onto the drive shaft to fit:Fiat 127, 128, Strada & X19 all modelsClassic Panda Early model..

This Inner Drive Shaft Boot fits into a three bolt metal flange and has a clip to hold the other end onto the drive shaftInner diameter of base: 73mmto fit:(FIAT) - NM CINQUECENTO (1992-1998)  all models (FIAT) - LV PANDA 4X2 RL/86(1985-1991) 750cc,903cc,999cc,1100cc ..

This Inner Drive Shaft Boot fits onto a metal flange and has a clip to hold the either end into placeInner diameter of base: 80mmto fit:(FIAT) - NM CINQUECENTO (1992-1998) all models (FIAT) - LV PANDA 4X2 RL/86(1985-1991) 750cc,903cc,999cc,1100cc (FIAT) - 2R PANDA 4X4 R/8..

This Inner Drive Shaft Boot fits into a three bolt flangeIt has a built in Oil Seal to stop oil leaking and fits onto the Drive Shaft with a incapsulated plastic Bush(No 10 in the diagram)to fit:PANDA 4X2 RL/86(1985 -1991) 750cc,903cc,999cc,1100cc PANDA 4X4 R/86 (1985 -1991) 99..

This Inner Drive Shaft Boot fits into a three bolt metal flange and has a clip to hold the other end onto the drive shaftIt comes with an inner bearing/oil thrower which fits onto the shaftThis Kit comes with a new Rubber Boot, Bearing & Clip (No 3,14 &15 in the diagram)Inner diamet..

This Inner Drive Shaft Boot fits onto a metal flange and has a clip to hold the either end into placeIt comes with an inner bearing/oil thrower which fits onto the shaftThis Kit comes with a new Rubber Boot, Bearing & two Clips (No 3,4,5 &15 in the diagram)Inner diameter of base: 80..

This Outer Drive Shaft Boot fits onto the Wheel end of the Drive Shaft at the CV JointDiameter at smaller Shaft End: 25mmDiameter at larger Joint End: 85mmto fit:STRADA Abarth 125/130TCCroma 2.0 CHT & IEPlease contact us with the full chassis number of the car ..

This Outer Drive Shaft Boot fits onto the Wheel end of the Drive Shaft at the CV JointDiameter at smaller Shaft End: 25mmDiameter at larger Joint End: 85mmto fit:STRADA Abarth 125/130TCCroma 2.0 CHT & IELancia BetaPlease contact us with the full chassis num..

This rubber Boot fits onto the cable and over the battery terminal to insulate itFits most Battery TypesFor the POSITIVE + Terminal Dimmensions:Length: 57mmWidth: 40mmDepth: 20mmInternal Diameter of Wire Cover: 15mmLength of Wire Cover: 35mm ..

The benefit of these tie straps over plastic ones is that they are made from non corrosive stainless steel They are mainly designed to be fitted to CV Boots which are under constant threat from water, heat and road grime..

Quality PartsMade by Pirelli This is a kit of TWO Steering Rack Rubber Boots and Clips to fit (A in diagram) to fit:Fiat 126 all modelsFiat 127,128 all modelsFiat Strada/Ritmo all models including 130TC AbarthFiat Regata all modelsFiat C..