Classic Fiat 126 Parts

Drive Shaft Clip(for 24mm Drive Shaft)to fit:Classic Fiat 500 F/L & R all models (from 1966 to 1974)Fiat 126 all modelsFiat 600If you have any questions or queries please contact our office for help..

Set of FOUR Bolts & Spring Washers to fit the drive shaft coupling and flangeFiat Part No: 16044121to fit:Classic Fiat 500 all modelsFiat 126 all modelsFiat 600If you have any queries or questions please contact our office for help..

Brand NewThis is a new improved high quality Drive Shaft KitLargest Diameter available 24/25mm (this measurement can vary between 22mm and 25mm)This kit consists of,2x Drive Shafts(24/25mm diameter)2x Drive Shaft Flange2x Shaft End Springs2x Clips2x Inner Boots ..

These Metal Nuts are not threaded but lock onto the end of the Drive Shaft inside the Gearbox to lock in to placeThere are TWO Nuts per Drive ShaftSold as a PAIR (2)to fit:Classic Fiat 500 all models N/D/F/L/R/GFiat 126 all modelsIf you have any questions please con..

This small Spring is located at the wheel end of each drive shaft to keep the tension and stop any knocking(for later larger type 24mm Drive Shaft)to fit:Classic Fiat 500 F/L & R (up to 1974)Fiat 126 all modelsIf you have any queries or questions please contact our..

This is the Dry Type standard Coil (NOT Oil Filled Type)This is an alternative and direct replacement to the standard Coil and works better in a hot engine bayResistance 1.75 ohm15 = POSITIVE1= NEGATIVEFits many different models including:Fiat 500 all models ..

This Hub has three studs for the Fan Pulley to attach onto and is attached onto the Dynamo to drive the Cooling FanSupplied with new Nuts and Locking Keyto fit:Classic Fiat 500 all modelsFiat 126 594cc all models (with Dynamo)If you have any questions please feel free to ask..

This rubber Boot fits onto the cable and over the Dynamo terminal to protect and insulate itto fit:Classic Fiat 500 all models (up to 1973)Fiat 126 594cc early models with Dynamo (up to 1976)Dimmensions:Total Length: 45mmWidth: 20mmDepth: 230mmInternal Diame..

This is a semi circle shaped metal key that fits into the shaft of an Dynamo to lock the Hub3mm Widthto fit:Classic Fiat 500 all models with DynamoFiat 126 (594cc with Dynamo)If you have any questions please contact us for help..

Insulated Black Earth StrapLength: 500mmTakes an 8mm fittingto fit:Classic Fiat 500 all models (up to 1973)Fiat 126 early models (up to 1978)If you have any questions please contact us for help..

Original Quality Branded Partto fit:Classic Fiat 500 (with electronic distributor fitted)Fiat 126 650cc & 704cc later models with flat type distributor cap (from 1978 to 1999)If you have any queries or questions please feel free to ask..

Electronic Indicator Flasher RelayPlastic Design3 Pin Fittingto fit:Classic Fiat 500 all modelsFiat 126 early modelsFiat 600 all modelsIf you have any questions please contact us..

Non Adjustable Electronic Type Voltage RegulatorThis part fits to the rear Bulkhead of vehicle and connects to the DynamoFitted to an Aluminium plate for coolingto fit:Classic Fiat 500 all models (with Dynamo)Fiat 126 all early models up to 1978 (with Dynamo)Fi..

Fitted between the Rocker Cover and the Air Filter Housing this rubber hose is very important tolet the engine breatheto fit:Classic Fiat 500 all models (up to 1974)Fiat 126 all air cooled models (up to 1999)If you have queries or questions please feel free to..

These Grommets fit either side of the aperture of the rear Engine Lid to make the opening and closingsmoother and keep the gaps consistentto fit:Classic Fiat 500 all models (NOT Giardiniera)If you have any questions or queries please feel free to ask..

This Bracket is fitted at the front and back of the engine as standard This is for ONE Bracketto fit:Classic Fiat 500 all modelsFiat 126 all modelsIf you have any questions please contact us for help..

This Bracket and Stud Kit is used to lower the engine block and avoid the Exhaust fromhitting the Rear Panelto fit:Classic Fiat 500 R all modelsFiat 126 all air cooled modelsIf you have any questions please contact us for help..

Brand NewMade in POLANDThis is an ECU for the late Polish 650cc Engine without a Distributor (OLD STYLE)to fit:Classic Fiat 500 (with Polish Distributor-less 650cc Engine fitted)Fiat 126 650cc (from 1994 on)If you have any questions please contact us for help..

Made in ItalyLength 60mmto fit:Classic Fiat 500 R all modelsFiat 126 all air cooled modelsIf you have any questions please contact us for help ..

Engine Mount Support Bracket/Plateto fit:Classic Fiat 500F/L/R (with 126 594cc or 650cc Engine fitted)Fiat 126 (594cc & 650cc) all modelsIf you have any questions please contact us for help..